Anritsu MG3642A Manuel d'utilisateur Page 55
- Page / 212
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SECTION 4 OPERATING INSTRUCTIONS
4-15
4.5.5 Switching the Output Signal On/Off
You can switch on and off the output signal that goes through the output connector by pressing the [RF Off/On] key.
When the output signal is cut off, the lamp of the [RF Off/On] key will light up.
An output level you set with the output signal cut off will become effective the next time you switch on the output
signal.
[RF Off/On] key
MG3641A/MG3642A front panel
- ANRITSU CORPORATION 1
- Safety Symbols 2
- For Safety 3
- Equipment Certificate 7
- Anritsu Warranty 7
- Anritsu Corporation Contact 7
- Notes On Export Management 8
- CE Conformity Marking 10
- 4. Authorized representative 11
- C-tick Conformity Marking 12
- Power Line Fuse Protection 13
- SECTION 1 19
- 1.2 Operation Manual 20
- 1.3 Composition of Devices 21
- 1.3.2 Options 22
- Table 1-3. Options 22
- 1.4 Application Parts 23
- 1.5 Specifications 24
- Specifications (continued) 25
- (0 to 50°C) 29
- ■ Option 22 (FSK encoder) 29
- SECTION 1 GENERAL 30
- SECTION 2 31
- PRECAUTION 31
- CAUTION 32
- SECTION 2 PRECAUTION 33
- WARNING CAUTION 34
- WARNING 35
- SECTION 3 37
- PANEL LAYOUT 37
- SECTION 3 PANEL LAYOUT 38
- 3.1.2 Rear panel layout 39
- 3.1.3 Panel layout diagram 40
- Fig. 3-2. Rear Panel 40
- Fig. 3-1. Front Panel 40
- OPERATING INSTRUCTIONS 41
- SECTION 4 41
- 4.1.1 Turning Power On 43
- 4.1.2 Turning Power Off 44
- 4.2 Explanation of Screens 45
- Chk SysGPIB Opt Trig 46
- Main Menu (2/2) 46
- [Preset] key 46
- MG3641A/MG3642A front panel 46
- 4.4 Setting the Frequency 48
- [Rel Freq] key 49
- [Shift] key 49
- 4.4.3 Frequency Offset 50
- [Level] key 51
- [Rel Level] key 52
- 4.5.3 Output Level Offset 53
- 4.5.4 Level Continuous Mode 54
- [RF Off/On] key 55
- Chk SysGPIB Opt Trig 57
- 4.6 Setting the Modulation 58
- [Modulation] key 59
- Mod Ofs MemAFSwp 68
- Main Menu (1/2) 68
- [Memory] 70
- (Memory Set) key 70
- [Memory] key 71
- 4.9.4 Clearing the Memory 73
- 4.10 Sweep Functions 75
- Main Menu (1) 76
- Sweep Auxiliary 79
- Output Connector 79
- MG3641A/MG3642A rear panel 79
- 4.11 Trigger Function 81
- Trigger Program 82
- No Trig Program 82
- Trig Input 83
- 4.12 Miscellaneous Functions 85
- 4.12.1 Setting Display On/Off 85
- Chk SysGPIB Opt Trig 86
- Mod Ofs Mem 90
- Data out of range 90
- Error messages 90
- SECTION 5 93
- MEASUREMENT 93
- SECTION 5 MEASUREMENT 100
- Disturbing wave input level 101
- SECTION 6 107
- 6.1.3 Setup example 108
- 6.1.4 Standard 109
- 6.2 Device Message List 110
- 6.2.4 Writing Commands 111
- Fig. 6-2. Writing Commands 111
- 6.2.5 Compounding Commands 112
- 6.2.6 Parameter 113
- 6.2.7 Unit 113
- 6.2.8 Command Tree 114
- SECTION 6 GPIB 115
- 6.3 Connecting the GPIB Cable 120
- Program message unit 121
- Numeric program data 122
- Logical program data 122
- Character program data 122
- Suffix data (unit) 122
- 6.4.2 Response message format 124
- 6.5 Status Message 126
- 6.5.5 SCPI error messages 131
- 6.6 Initializing Device 133
- 6.7.1 Frequency subsystem 134
- 6.7.2 Output level subsystem 138
- Response Level offset value 140
- 6.7.3 AM subsystem 144
- 6.7.4 FM subsystem 145
- 6.7.5 PM subsystem 147
- 6.7.7 MEMORY subsystem 151
- 6.7.8 Display subsystem 153
- 6.7.9 System subsystem 154
- 6.7.10 Status subsystem 155
- 6.8 IEEE488.2 Common Command 157
- MG3641A/MG3642A 159
- MS2651A spectrum analyzer 159
- 6.10.1 Outline 162
- (3) Output level 163
- SECTION 7 169
- PERFORMANCE TEST 169
- SECTION 7 PERFORMANCE TEST 170
- 7.3 Performance Test 171
- 7.3.1 Output frequency 172
- Power meter 173
- +15 to Ma-8) 174
- (5) Note on test 179
- SECTION 8 181
- CALIBRATION 181
- 8.3 Calibration 182
- SECTION 8 CALIBRATION 184
- SECTION 9 185
- STORAGE AND TRANSPORTATION 185
- 9.3.1 Repacking 186
- 9.3.2 Transportation 186
- APPENDIX A 187
- INITIAL FACTORY SETTINGS 187
- APPENDIX B 191
- FUNCTION-KEY TRANSITION 191
- [Frequency offset value] 193
- 0.00 dB 193
- APPENDIX C 197
- FRONT AND REAR PANEL LAYOUT 197
- APPENDIX D 201
- APPENDIX D INDEX 202
- 3.1.1，4.4.3，4.5.3 203
- APPENDIX E 207
- Copy this at the measurement 212
Produits connexes et manuels pour Mesure, test et contrôle Anritsu MG3642A
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.226 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels