Anritsu Site Master S332D Manuel d'utilisateur télécharger pdf (Page 8)

Specifications

All specifications apply when the unit is calibrated at

ambient temperature after a five minute warm up. Typical

values are given for reference, and are not guaranteed.

Cable and Antenna Analyzer

Frequency Range: 25 MHz to 4.0 GHz

Frequency Accuracy: ≤±75 ppm @ +25˚C

Frequency Resolution: 100 kHz

Output Power: <0 dBm (–10 dBm nominal)

Immunity to Interfering Signals:

on-channel +17 dBm

on-frequency –5 dBm

Measurement Speed: ≤3.5 msec / data point (CW ON)

Number of Data Points: 130, 259, 517

Return Loss: Range: 0.00 to 60.00 dB

Resolution: 0.01 dB

VSWR: Range: 1.00 to 65.00

Resolution: 0.01

Cable Loss: Range: 0.00 to 30.00 dB

Resolution: 0.01 dB

Measurement Accuracy: >42 dB corrected directivity

after calibration

Distance-To-Fault

Vertical Range: Return Loss: 0.00 to 60.00 dB

VSWR: 1.00 to 65.00

Horizontal Range: 0 to (# of data pts –1) x

Resolution to a maximum of 1197m (3929 ft),

# of data pts = 130, 259 or 517

Horizontal Resolution (Rectangular Windowing):

Resolution (meter) = (1.5 x 10

) x (Vp)/DF

Where Vp is the cable's relative propagation

velocity and where DF is the stop frequency

minus the start frequency (in Hz).

Spectrum Analyzer (S332D)

Frequency:

Frequency Range: 100 kHz to 3.0 GHz (tuneable to

9 kHz)

Frequency Reference (Internal Timebase):

Aging: ±1 ppm/yr

Accuracy: ±2 ppm

Frequency Span:

10 Hz to 2.99 GHz in 1, 2, 5

step selections in auto mode, plus zero span

Sweep Time: ≤1.1 sec full span;

≤50

sec to 20 sec selectable in zero span

Resolution Bandwidth (–3 dB):

100 Hz to 1 MHz in 1-3 sequence

5% Accuracy

Video Bandwidth (–3 dB):

3 Hz to 1 MHz in 1-3 sequence ±5% Accuracy typical

SSB Phase Noise (1 GHz) @ 30 kHz Offset:

≤

–75 dBc/Hz

Spurious Responses Input Related: ≤–45 dBc

Spurious Residual Responses:

≤

–90 dBm,

≥10 MHz

≤–80 dBm, <10 MHz

(10 kHz RBW

, pre-amp on)

Amplitude:

otal Level Accuracy:

±1 dB typical (±1.5 dBm max), ≥10 MHz to 3 GHz

2 dB typical, <10 MHz

for input signal levels

≥–60 dBm,

excludes input VSWR mismatch

Measurement Range: +20 dBm to –135 dBm

Input Attenuator Range: 0 to 51 dB,

selected manually or automatically coupled to

the reference level. Resolution in 1 dB steps.

Displayed Average Noise Level:

≤–135 dBm, ≥10 MHz (preamp on)

≤–115 dBm, <10 MHz (preamp on)

for input terminated, 0 dB attenuation,

RMS detection, 100 Hz RBW

Dynamic Range: >65 dB, typical

Display Range: 1 to 15 dB/division, in 1 dB steps,

10 divisions displayed

Scale Units: dBm, dBV, dBmV, dBµV, V, W

RF Input VSWR: (with ≥20 dB atten.), 1.5:1 typical,

(10 MHz to 2.4 GHz)

Bias Tee (Option 10 S332D only)

Voltage: +18 Vdc

Current: 1A peak 150 ms, 300 mA max steady state

Transmission Measurement

(Option 21 S332D only)

Freqency Range: 25 MHz to 3 GHz

Frequency Resolution: 10 Hz

Output Power Level: –10 dBm typical

Output Impedence: 50Ω

Power Meter (Option 29)

Frequency Range: 3 MHz to 3.0 GHz

Measurement Range: –80 dBm to +20 dBm

(+80 dBm with 60 dB external attenuator)

Display Range: –80 dBm to +80 dBm

Offset Range: 0 to +60 dB

Accuracy**: ±1 dB typical (±1.5 dBm max), >2 GHz to 3 GHz

±0.5 dB typical (±1 dB max), ≥10 MHz to 2 GHz

±2 dB typical, 3 MHz to <10 MHz

VSWR: 1.5:1 typical (Pin >–30 dBm, 10 MHz to 2.4 GHz)

Maximum Power: +20 dBm (0.1W) without external attenuator

**(Excludes Input VSWR)

T1 Analyzer (Option 50 S331D only)

Line Coding: AMI, B8ZS

Framing Modes:

D4 (Superframe)

ESF (Extended Superframe)

Connection Configurations:

Terminate (100Ω)

Bridge (

≥1000Ω)

Monitor (Connect via 20 dB pad in DSX)

Receiver Sensitivity:

0 to –36 dBdsx

Transmit Level: 0 dB, –7.5 dB, and –15 dB

Clock Sources: External

Internal: 1.544 MHz

30 ppm

Pulse Shapes: Conform to ANSI T1.403

Pattern Generation and Detection:

PRBS: 2-9, 2-11, 2-15,

2-20, 2-23 Inverted and non-inverted, QRSS,

1-in-8 (1-in-7), 2-in-8, 3-in-24, All ones, All zeros,

T1-Daly, User defined (

≤32 bits)

Circuit Status Reports:

Carrier present, Frame ID

and Sync., Pattern ID and Sync.

Alarm Detection: AIS (Blue Alarm), RAI (Yellow Alarm)

Error Detection:

Frame Bits, Bit, BER, BPV

, CRC, Error Sec

Error Insertion: Bit, BPV, Framing Bits, RAI, AIS

Loopback Modes:

Self loop, CSU, NIU, User

defined, In-band or Data Link

Level Measurements: Vp-p (± 5%)

Data Log: Continuous, up to 48 hrs.

E1 Analyzer (Option 50 S331D only)

Line Coding: AMI, HDB3

Framing Modes: PCM30, PCM30CRC, PCM31,

PCM31CRC

Connection Configurations:

Terminate (75Ω, 120Ω)

Bridge (≥1000Ω)

Monitor (Connect via 20 dB pad in DSX)

Receiver Sensitivity: 0 to –43 dB

Clock Sources:

External

Internal 2.048 MHz ±30 ppm

Pulse Shapes: Conform to ITU G.703

Pattern Generation and Detection:

PRBS: 2-9, 2-11, 2-15, 2-20, 2-23 Inverted and

non-inverted, QRSS, 1-in-8 (1-in-7), 2-in-8, 3-in-24,

All ones, All zeros, T1-Daly, User defined (

≤32 bits)

Circuit Status Reports: Carrier present, Frame ID

and Sync., Pattern ID and Sync.

Alarm Detection: AIS, RAI, MMF

Error Detection: Frame Bits, Bit, BER, BPV, CRC, E-Bits,

Error Sec

Error Insertion: Bit, BPV, Framing Bits, RAI, AIS

Loopback Modes: Self loopback

Level Measurements: Vp-p (±5%)

Data Log: Continuous, up to 48 hrs.

General

Language Support: Chinese, English, French, German,

Japanese, Spanish,

Internal Trace Memory: 200 traces

Setup Configuration: S332D - 20, S331D - 25

Display: VGA monochrome or VGA color LCD (Option 3)

with adjustable backlight

Inputs and Outputs Ports:

RF Out: Type N, female, 50Ω

Maximum Input without Damage: +23 dBm, ± 50 VDC

RF In: Type N, female, 50Ω

Maximum Input without Damage: +43 dBm (peak), ± 50 VDC

Ext. Trig In: BNC, female (5V TTL) (S332D Models only)

Ext. Freq Ref In (2 to 20 MHz): Shared BNC, female,

50Ω, (–15 dBm to +10 dBm) (S332D Models only)

T1/E1 (Receive & T

ransmit):

Bantam Jack

(S331D Models with Option 50 only)

Serial Interface: RS-232 9 pin D-sub, three wire serial

Electromagnetic Compatibility:

Meets European

Community requirements for CE marking

Safety:

Conforms to EN 61010-1 for Class 1

portable equipment

Temperature:

Operating: –10°C to 55°C, humidity 85% or less

Non-operating:

–51

C to +71

C (Recommend the

battery be stored separately between 0°C and +40°C

for any prolonged non-operating storage period.)

Environmental:

MIL-PRF-28800F Class 2

Power Supply:

External DC Input:

+12.5 to +15 volt dc, 3A max

Internal: NiMH battery: 10.8 volts, 1800 mAH

Dimensions:

Size (w x h x d): 25.4 cm x 17.8 cm x 6.1 cm

(10.0 in x 7.0 in x 2.4 in)

Weight: <2.28 kg (<5 lbs) includes battery

1 2 3 4 5 6 7 8 9

Commentaires sur ces manuels

Pas de commentaire

Anritsu Site Master S332D Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau Anritsu Site Master S332D